Masonry Contractor Work Around New Storefront Door Openings

Commercial glass storefront doors beside a brick masonry wall, showing entrance framing and threshold details for a masonry contractor in Auburn, Alabama.

Cutting a new storefront door into an old brick wall looks quick on a drawing, but a masonry contractor knows the wall usually has a few surprises waiting. That wall may carry floors above, hide old repairs, or hold moisture you can’t see from the sidewalk. Get the opening wrong and you end up with cracked brick, leaks around the frame, or a door that won’t sit square.

Bring the mason in before the storefront is ordered. Brick size, wall thickness, and support above the opening all affect the final door dimensions. Planning those together saves rework and keeps the entrance looking like it belongs on the building.

Assessing Existing Masonry Around Proposed Storefront Door Openings

Start with a close look at the wall. A masonry contractor checks for cracks, loose brick, soft or missing mortar, old patches, and signs of water damage near the planned opening. Older storefronts often hide filled-in doors or windows that change how the wall behaves once it’s cut.

Wall type matters too. Some walls are solid brick several layers thick, while others are a brick face over block or framing. Knowing what’s behind the face brick tells you how the cut, the support, and the finish work will go.

Coordinating Door Dimensions With Brick and Masonry Wall Layouts

Storefront frames come in set sizes, and so does brick. When the opening lines up with full or half bricks, the edges look clean and need fewer cut pieces. A small adjustment in the frame order can save a lot of awkward cutting.

Match the opening to the wall’s pattern. Many older buildings use running bond or common bond with header rows every few courses, and the new edges should follow that pattern. Talk through the rough opening size with both your storefront supplier and your mason before anything gets ordered.

Planning Structural Support Before Modifying Load-Bearing Masonry

Never cut a large opening in a bearing wall without a support plan. Walls that carry floors or a roof need a lintel or beam over the new opening, and its size depends on the load above. A structural engineer usually designs that support, and permit needs can vary by local code and project scope.

Temporary shoring holds the wall up while the opening is cut and the new lintel goes in. A masonry contractor works with the engineer and general contractor to set the shoring, cut the brick, and seat the lintel on solid bearing at each side. Skipped steps here are how storefront projects end up with sagging brick and cracked walls.

Masonry Contractor Work for Door Jambs and Threshold Transitions

Rebuilding the jambs is where the opening starts to look finished. Cut brick edges get toothed in or replaced with whole units so the sides are straight, plumb, and solid. Clean jambs also give the storefront installer a good surface to anchor and seal against.

Thresholds need just as much thought. The floor inside, the sidewalk outside, and the door sill all have to meet without trip edges or spots that trap water. Accessibility rules may affect threshold height and slope, so confirm them with your designer before any brick or stone is set at the base. Some owners add brick pavers or stone pavers at the entry to tie the new door into the sidewalk.

Frequently Asked Questions

Can a new door opening be cut into an existing brick wall?

Yes, in most cases, but the wall has to be checked first. Bearing walls need a lintel or beam and often temporary shoring. Wall condition, thickness, and what sits above all shape the plan. A structural engineer and mason should review the wall before any cutting starts.

Who designs the support above a new storefront opening?

A structural engineer usually designs the lintel or beam for a load-bearing wall. The mason and general contractor then install it according to that design. Permit requirements can vary by local code and project scope. Ask your general contractor who will provide stamped drawings if they’re needed.

How do masons match new brick to an old storefront wall?

They compare color, size, texture, and mortar joints with the existing wall. Brick salvaged from the cut opening can sometimes be reused at the jambs. When there isn’t enough salvage, the mason looks for close matches from suppliers. Mortar color and strength are matched too so the repair blends in.

What causes leaks around new storefront doors in masonry walls?

Missing or poorly placed flashing is a common cause. Gaps in the sealant between brick and frame also let water in. Blocked weep holes can trap moisture inside the wall. Coordinating flashing and sealant details between trades prevents most of these problems.

When should a masonry contractor be brought into a storefront project?

Bring in a masonry contractor before the storefront system is ordered. Early input helps set door sizes that fit the brick pattern. It also leaves time to plan support, shoring, and permits. Late involvement often leads to awkward cuts and change orders.